The Finish Your Specific Product Depends On.

Surface finish is critical to your specific product. Finish, hardness, and coating are engineered to what your process demands, from mirror finishes for transfer-critical work, to hard chrome for wear and release, to textured surfaces for grip. On a precision line the surface is the working part, and we treat it that way.

Since 1959 Engineered Since 1959
2,000+ Formulations In-House, We Own Them
Inspection TIR to 0.0002″
ISO 9001:2015 Quality Management

Resurface or Replace?

When the Surface Wears, the Product Shows It First.

Transfer goes uneven, release gets sticky, the web starts to slip, or a finish that was mirror when it shipped is hazing well before it should. Each one shows up in the product before it shows up on the roller, and by then scrap is already counting against the shift. If the core and geometry are sound, the fix is usually the surface: regrind and polish it back to finish, or plate or coat it for the wear and release the position actually needs.

An evaluation tells you which. We look at what the surface has to do, what it runs against, and what it is wearing on, then specify finish, hardness, and coating to that, rather than to whatever the last roller happened to have.

  • Uneven Transfer
  • Sticky Release
  • Web Slip
  • Finish Hazing
  • Chrome Worn Through
  • Surface Scoring
  • Coating Flaking

The ABBA Standard

The Surface Is Specified, Not Just Finished.

Every roller here leaves with a surface that was chosen for the job. Finish, hardness, and coating are fixed on the approval drawing you sign off on before we build: a mirror finish where the product has to transfer or release clean, hard chrome where wear and release are what the position demands, a textured surface where the web has to grip. Surface-finish control is held to spec. As low as 0–1 μin Ra, various finishes available.

Then the finish is measured, and every critical tolerance is verified and documented before shipment.

In-House Material Development
Application Engineering & Review
Reverse Engineering & Design Support
Verified Tolerances
Approval Drawing Sign-Off
Responsive Lead Times & Expedite Options
Request a Roller Evaluation

From Application Review to Verification

How Surface
Technologies Work

Every surface job starts with what the surface has to do and is carried through specification, grinding and polishing, plating or coating, and final verification, so the finish on the roller is the finish on the drawing.

Start with What the Surface Has to Do.

We start with the job the surface does in your process: transfer a fluid or a film evenly, release clean, hold up to wear, or grip the web. Then what it runs against, what it runs in, and how it has been failing. That review sets the finish, hardness, and coating before anything goes on the drawing.

  • Transfer & Release
  • Wear & Abrasion
  • Grip & Traction
  • Chemical & Heat Exposure
  • Failure-Mode Review

Finish, Hardness, and Coating Fixed on the Drawing.

The surface is specified the way the geometry is: finish, hardness, and coating called out on the approval drawing you sign off on before we build. Mirror finish, hard chrome, anodizing, a coating, or a texture, each is chosen for the job the surface has to do, and the finish target is written down so it can be measured.

  • Approval Drawing
  • Finish Called Out
  • Hardness Specified
  • Chrome, Anodizing & Coatings
  • Texture Where It Grips

Ground True, Then Polished to the Finish.

The roller is precision ground to the drawing first, so the finish goes onto a surface that is already true, then polished to the specified finish. Mirror finishes for transfer-critical work are brought down as low as 0–1 μin Ra, with various finishes available where the process wants something else. Existing rollers are resurfaced the same way.

  • Precision Grinding
  • Mirror-Finish Polishing
  • Surface-Finish Control
  • Cylindricity To 0.0003″
  • Resurfacing of Existing Rollers

Hard Chrome, Anodizing, and Coatings for the Position.

Where the position demands wear resistance and release, the roller is hard chrome plated. Where an aluminum roller needs a hard, protected surface, it is anodized. Where the process calls for a specific surface, a coating goes on. Plating and coating go over a ground and finished surface and are brought back to the finish the drawing calls for.

  • Hard Chrome Plating
  • Anodizing
  • Coatings
  • Post-Plate Finishing
  • Wear & Release

The Finish Is Measured Before It Ships.

The surface finish is measured against the number on the drawing, and runout, cylindricity, and every other critical tolerance are verified and documented before shipment. If the finish is not what the drawing says, it does not ship.

  • Surface-Finish Measurement
  • TIR To 0.0002″
  • Runout & Cylindricity Verification
  • Quality Documentation

FAQs

Surface Technologies: Common Questions

What Is Hard Chrome Plating on a Roller For?
Wear and release. Hard chrome gives the roller a hard, low-friction surface that holds up to abrasion and lets product release clean, which is why it is specified on coating, metering, and heat-transfer positions. It goes on over a ground and finished surface and is brought back to the finish the drawing calls for. See Coating Rollers and Heat-Transfer Rollers.
Can You Resurface a Roller Instead of Replacing It?
Usually, yes. If the core and journals are sound and the geometry can be brought back, an existing roller can be reground and polished to finish, or stripped and replated, for a fraction of replacement cost. If the surface has failed because the cover or compound under it is wrong, we will tell you, and recover it instead. See Recover & Repair.
How Fine a Surface Finish Can You Hold?
As low as 0–1 μin Ra, various finishes available. The finish is called out on the approval drawing and measured before shipment, so a mirror finish for transfer-critical work is a number that is verified, not a description on a quote.
Which Finish Does My Roller Need?
It depends on what the surface has to do. Transfer-critical work usually wants a mirror finish so the fluid or film lays down evenly. Wear and release positions usually want hard chrome. Positions where the web has to grip usually want a textured surface. Tell us what’s happening on the line, and an engineer will specify the finish, hardness, and coating to the job rather than to what the last roller had. See Engineering.
Do You Finish Rubber and Urethane Covers Too?
Yes. Surface finish is specified on covered rollers the same way it is on metal: ground true, then finished to what the process needs, from a smooth finish for coating and laminating to a texture for traction. The compound comes first, though. On a covered roller the finish is only as good as what is under it. See Rubber-Coated Rollers, Polyurethane Rollers, and Material Development.
How Long Does Surface Work Take?
Typically about three to four weeks for a recover, depending on size and current shop load. New fabrications generally run longer: roughly a month for straightforward builds, and up to two to three months for complex ones. Expedite is available on request and review. Request a roller evaluation to get started. An engineer reviews it and reaches out fast.

Roller Evaluation

Tell Us What the Surface Has to Do.

Tell us what’s happening on the line, or send the roller and the drawing if you have one. An engineer reviews it and reaches out fast.