2,000+ Formulations. Engineered to Your Chemistry, Temperature, and Wear.

We develop and own our rubber formulas, milled and batch-tested in our own lab, engineered to your chemistry, temperature, and wear demands rather than pulled off a shelf in a stock durometer. On a recover we can lab-match your incoming material, or improve on it, which is usually where the wear-life gain comes from.

Since 1959 Engineered Since 1959
2,000+ Formulations In-House, We Own Them
Inspection TIR to 0.0002″
ISO 9001:2015 Quality Management

When the Compound Is the Problem

When a Position Keeps Failing, It Is Usually the Compound, Not the Roller.

A cover that swells in the solvent, hardens under heat, or wears through in a fraction of the life it should have is not a grinding problem. It is a materials problem, and a stock durometer pulled off a shelf will not fix it. Recovering the roller with the same compound puts the same failure back on the line.

Material development starts with the position: the chemistry the cover sits in, the temperature it runs at, and the load and wear it takes. The formulation is engineered to that, and batch-tested before it goes on.

  • Chemical Swelling
  • Heat Hardening
  • Premature Wear
  • Cover Cracking
  • Wrong Durometer
  • Batch Inconsistency
  • Unknown Compound

The ABBA Standard

The Compound Is Engineered Here, Milled Here, and Tested Here Before It Goes On.

We develop and own 2,000+ formulations, milled and batch-tested in our own lab. Each one was built for a real position: a chemistry, a temperature, a wear demand. When yours is not among them, we formulate a new one. On a recover, we can cut a sample of the incoming cover and lab-match the material you are running today, or improve on it.

Polyurethane and specialty elastomers are selected here too, and food-grade compounds are formulated where the application requires them. Whatever goes on the roller is batch-tested before covering, then verified for hardness and finish before it ships.

In-House Material Development
Application Engineering & Review
Reverse Engineering & Design Support
Verified Tolerances
Approval Drawing Sign-Off
Responsive Lead Times & Expedite Options
Request a Roller Evaluation

From Application Review to Verification

How Material
Development Works

Every compound begins with the position it will run in and is carried through selection or formulation, lab testing, milling, and covering to final verification, so the cover on the roller is the cover that was engineered for it.

It Starts with What the Cover Will See.

Before any compound is chosen, an engineer reviews the position: the chemistry the cover sits in, the temperature it runs at, the load across the face, and the wear the surface takes. A worn roller or a sample of the incoming cover tells us more than a catalog would.

  • Chemical Exposure
  • Operating Temperature
  • Load & Pressure
  • Wear & Abrasion
  • Application Review

Selected From 2,000+ Formulations, or Built New.

The review points to a formulation we already own, developed for a position like yours, or to a new one engineered to your chemistry, temperature, and wear. Rubber, polyurethane, and specialty elastomers are all selected here, and food-grade compounds are formulated where the application requires them.

  • 2,000+ Proprietary Formulations
  • New Formulation Development
  • Rubber, Urethane & Specialty Elastomers
  • Hardness Selection
  • Food-Grade Where Required

Matched to What You Run, and Tested Before It Goes On.

On a recover we can cut a sample of the incoming cover and lab-match the material you are running today, or improve on it where the wear life says we should. Every batch is tested in our own rubber-chemistry lab before it is cleared for covering, so what goes on the roller is what the formulation says it is.

  • Incoming-Material Lab Matching
  • In-House Rubber-Chemistry Lab
  • Batch Testing
  • Hardness Check

Milled In-House, Then Applied Under Process Control.

The tested batch is milled in our own shop and applied to the core, bonded, and cured using controlled processes designed for consistent, repeatable results. The compound and the covering are handled by the same people on the same schedule, so nothing is lost between the lab and the floor.

  • In-House Milling
  • Rubber & Urethane Covering
  • Bonding
  • Controlled Curing

Hardness and Finish Verified Before It Ships.

After grinding and finishing, the cover is checked against the drawing: hardness verified against the formulation, surface finish verified to the specification, and every critical tolerance verified and documented before shipment.

  • Hardness Verification
  • Surface-Finish Verification
  • Runout & Cylindricity Verification
  • Quality Documentation

FAQs

Material Development: Common Questions

What Does Material Development Mean at ABBA?
It means the compound on your roller is engineered to the position it runs in, not pulled off a shelf in a stock durometer. We develop and own 2,000+ formulations, milled and batch-tested in our own rubber-chemistry lab, and we formulate new ones when the application calls for it. The result is a cover matched to your chemistry, temperature, and wear, verified for hardness and finish before it ships, which is usually where the wear-life gain comes from.
Can You Match the Compound We Are Running Now?
Yes. On a recover we can cut a sample of the incoming cover and lab-match the material you are running today. If that material is what is cutting your wear life short, we will tell you and recommend a better-performing formulation instead. See Recover & Repair.
Do You Work With Polyurethane and Specialty Elastomers, or Only Rubber?
All three. Rubber compounds are formulated and milled in-house. Polyurethane and specialty elastomers are selected here as well, matched to the load, abrasion, chemistry, and temperature of the position. See Polyurethane Rollers and Rubber-Coated Rollers.
Can You Formulate a Food-Grade Compound?
Yes. Food-grade compounds are formulated where the application requires them. Tell us what the roller contacts and how it is cleaned, and the compound is engineered to that.
What Do You Need From Us to Select or Develop a Compound?
The position and what it sees: the chemistry, the temperature, the load, and how the current cover is failing. A worn roller or a sample of the existing cover is the best input we can get, because the wear pattern tells us what the compound has to resist. A drawing helps but is not required: we can reverse-engineer from the roller itself and produce an approval drawing you sign off on before we build. See Engineering.
How Long Does a Roller With a Custom Compound Take?
Typically about three to four weeks for a recover, depending on size and current shop load. New fabrications generally run longer: roughly a month for straightforward builds, and up to two to three months for complex ones. Expedite is available on request and review.

Roller Evaluation

Tell Us What the Cover Has to Survive.

Tell us what’s happening on the line, or send a sample of the cover you are running. An engineer reviews it and reaches out fast.