Coating Rollers Where the Compound and the Finish Are the Whole Job.

The roller meets the coating, and small differences in surface and material show up immediately in transfer, coat weight, and release. We engineer coating and application rollers, and the compounds behind them, to the chemistry you are actually running, with surface finishes held to spec.

Since 1959 Engineered Since 1959
2,000+ Formulations In-House, We Own Them
Inspection TIR to 0.0002″
ISO 9001:2015 Quality Management

What Kills Rollers on an Adhesive Coating Line

The Roller Sets the Coat Weight. Anything Wrong with It Runs the Full Length of the Roll.

Adhesive coating rollers run in solvent-based, water-based, and UV-curable chemistries, and the cover is in the fluid for every hour of the shift. A compound that is not matched to the adhesive swells, softens, or glazes, and the transfer drifts with it. A finish that is off the drawing changes how much the roller picks up and how cleanly it lets go, so coat weight wanders and release suffers. Runout in a coating or metering roller puts a repeating band into the coat. Adhesive that builds on the cover, or a nip that is uneven across the face, leaves streaks, voids, and edge bead that only show up when the roll is unwound.

The failure modes are different in every position, which is why we engineer to the position and the chemistry, not to a generic “coating roller”.

  • Coat-Weight Variation
  • Poor Release
  • Cover Swelling
  • Adhesive Build-Up
  • Streaks and Voids
  • Runout Banding
  • Lost Vendor

The ABBA Standard

We Engineer to the Position, Not to a Part Number.

Coating, application, slot-die coating, metering, nip, idler: each position has its own compound, finish, hardness, and geometry, and each fails in its own way. We start from the position and the chemistry, with covers from 2,000+ in-house formulations, milled and batch-tested in our own lab, so the cover is matched to the adhesive it will run in, and the finish is written on the drawing and measured before the roller ships.

Every roller is verified before it ships, on an approval drawing you signed off before we built it.

In-House Material Development
Application Engineering & Review
Reverse Engineering & Design Support
Verified Tolerances
Approval Drawing Sign-Off
Responsive Lead Times & Expedite Options
Request a Roller Evaluation

Positions We Engineer

The Positions on an Adhesive Coating Line.

Each position asks something different of the roller. Find yours, then the roller type that answers it.

FAQs

Adhesives & Tape Rollers: Common Questions

Which Adhesives & Tape Roller Positions Do You Engineer?
Coating, application, slot-die coating, metering, nip, and idler positions, for both OEM coating equipment and installed lines. If your position is not listed, tell us what it does and we will tell you whether we are the right fit.
Will the Cover Hold Up in Our Adhesive Chemistry?
That is the first question we ask. Solvent-based, water-based, and UV-curable adhesives each attack a cover differently, and the wrong compound swells, softens, or glazes in service. We select the compound from the chemistry, the release the position needs, and the hardness the nip calls for, from 2,000+ in-house formulations milled and batch-tested in our own lab. We can lab-match the cover you are running today or improve on it where the wear life says it should. See Material Development.
What Causes Coat-Weight Variation on a Tape Line?
Usually runout in the coating or metering roller, a finish that is off the drawing, a cover that has swollen or hardened in the adhesive, or a hardness that is wrong for the metering nip. Each leaves a different pattern on the web. Bands that repeat once per revolution point to runout; streaks that run the length of the roll point to the finish or the cover. The roller evaluation identifies which one it is before anything is quoted.
What Surface Finish Should an Adhesive Coating Roller Have?
The finish sets how the roller picks up and releases the adhesive, so it is specified to the chemistry and the coat weight rather than left to a default. A smoother finish releases more cleanly; a finish with more texture carries more fluid. We write the finish on the approval drawing and measure it before the roller ships. As low as 0–1 μin Ra, various finishes available. See Surface Technologies.
Should We Recover Our Coating Rollers or Buy New?
If the core is sound, recovering restores the roller to spec for a fraction of replacement cost, and often with better wear life than what you had, because we can put a compound back on that is matched to the adhesive the old one was not. If the core is damaged or the design was never right for the position, we will say so and quote the fabrication. See Recover & Repair.
How Do I Get Started?
Request a roller evaluation. An ABBA engineer reviews the positions in question and gives you a report with picture and dimensional evidence of what is worn and what to do about it.

Roller Evaluation

Put an Engineer on Your Coating Line.

Tell us which position is costing you coat weight, release, or uptime.