The Wheel Is What Lets the Robot Do What the Others Can’t.

In high-throughput warehouse automation, the wheel isn’t a commodity. It is a performance component. Grip, wear life, consistency, and noise determine how fast and how reliably a fleet moves. We engineer wheel and caster compounds to the duty cycle, floor surface, and load your robots actually see, and we own the formulations, so we tune to your platform instead of handing you a stock durometer.

Since 1959 Engineered Since 1959
2,000+ Formulations In-House, We Own Them
Inspection TIR to 0.0002″
ISO 9001:2015 Quality Management

What Kills Rollers and Wheels on a Robot Fleet

A Bad Wheel Doesn’t Stop One Robot. It Slows the Whole Fleet.

On a warehouse floor the wheel is the only part of the robot that touches the building. When the compound is wrong for the floor, the load, or the duty cycle, the failures show up fast and all at once: grip that falls off on sealed concrete, flat-spotting on a robot that parks under load, chunking at the shoulder of a wheel that corners hard, and a tread that wears through before its scheduled swap. Noise climbs. Floor coatings scuff and gouge. And when wheels vary from one robot to the next, the whole fleet ends up tuned to its worst wheel.

The failure modes differ by position, which is why we engineer to the drive wheel, the caster, and the end-effector roller separately, not to a generic “robot wheel”.

  • Grip Loss
  • Flat-Spotting
  • Chunking
  • Noise
  • Short Wear Life
  • Floor Damage
  • Wheel-to-Wheel Variation

The ABBA Standard

We Engineer to the Platform, Not to a Part Number.

Drive wheels, casters, end-effector rollers, traction and load positions: each asks something different of the compound, the tread geometry, and the bond to the hub, and each fails in its own way. We start from the duty cycle, the floor, and the load the platform actually sees, with compounds from 2,000+ in-house formulations that we own, mill, and batch-test in our own lab, so the wheel is tuned to your robot instead of pulled from a stock durometer.

Every wheel and caster is verified before it ships, on an approval drawing you sign off on before we build.

In-House Material Development
Application Engineering & Review
Reverse Engineering & Design Support
Verified Tolerances
Approval Drawing Sign-Off
Responsive Lead Times & Expedite Options
Request a Roller Evaluation

Wheels & Casters

The Wheels and Positions We Engineer.

Each position asks something different of the wheel. Find yours, then the compound and the build that answer it.

  • Drive Wheels

    The wheel that moves the robot. Grip on the floor it actually runs on, a tread that resists flat-spotting under a parked load, and a bond to the hub that holds through every start and stop.

  • Casters

    The caster wheel carries the load the drive wheel steers. It has to roll without shimmy, flat-spot, or floor marking, and roll the same on the last robot in the fleet as on the first.

  • End-Effector Rollers

    Rollers at the gripper or the pick point that handle product without marking it: compound, hardness, and finish matched to what the robot actually touches.

  • Traction

    Where the platform climbs, corners, or accelerates under load, the compound sets how much grip is there before the wheel slips. We tune it to the floor and the duty cycle, not to a catalog number.

  • Load

    Wheels and casters that carry the heaviest payloads without deflection, heat build-up, or chunking, with the tread bonded to a hub built for the load.

FAQs

Robot Wheels and Casters: Common Questions

Which Robot Wheel and Caster Positions Do You Engineer?
Drive wheels, casters, end-effector rollers, and the traction and load positions on mobile platforms and automated handling equipment, for both OEM builds and fleets already on the floor. If your position is not listed, tell us what it does and we will tell you whether we are the right fit.
Can You Match a Compound to Our Floor and Duty Cycle?
Yes. That is the point of owning the formulations. We compound in our own lab, from 2,000+ formulations we mill and batch-test ourselves, so grip, wear life, and noise can be tuned to the floor surface, the load, and the duty cycle your robots actually run, instead of picked from a stock durometer.
Do You Make Polyurethane Wheels or Rubber Wheels?
Both. Polyurethane where wear life and load lead, rubber where grip, noise, and floor protection lead, and a compound formulated to the position where neither is the right fit. See Polyurethane Rollers and Rubber-Coated Rollers.
How Do You Keep Wheels Consistent Across a Fleet?
The same way we keep a roller consistent across a production run. The compound is milled and batch-tested in our own lab, the wheel is ground to the same geometry every time, and every critical tolerance is verified before shipment, so the last wheel in the order performs like the first.
Can You Recover a Worn Wheel, or Does It Have to Be Replaced?
If the hub is sound, we can recover it: strip the worn tread, put a new or better-matched compound back on, and grind it to spec, for a fraction of replacement cost, and often with better wear life than what you had. If the hub is damaged or the design was never right for the position, we will say so and quote the fabrication. See Recover & Repair.
How Do I Get Started?
Request a roller evaluation. Send us a worn wheel, a spare, or a drawing, and tell us what’s happening on the floor. An engineer reviews it and reaches out fast.

Roller Evaluation

Put an Engineer on Your Fleet.

Tell us which wheel is slowing the fleet.