Lines Measured by the Hour, on Positions That Can’t Go Down.
Tissue and towel lines run continuously and are measured in dollars per hour. When a position fails, or wears out faster than it should, you are not replacing a part. You are losing run time and yield. We engineer the specific positions these lines depend on, matched to your speed, temperature, and surface demands, including food-grade and FDA-compliant compounds where the application requires them.
What Kills Rollers on a Tissue and Towel Line
A Worn Position Doesn’t Stop the Line. It Shows Up in Yield First.
Tissue and towel lines run hot, fast, and around the clock, against a web that is light, absorbent, and easy to mark. An embossing roller that has hardened with heat or lost its pattern definition stops delivering the bulk and softness the product is sold on. A glue applicator whose finish has changed meters too much adhesive, or too little, and the plies separate or the glue bleeds through. A rider or winder roller that is out of round, or has picked up a flat spot, winds a soft log that telescopes. None of these stops the line outright. They show up as culled logs, short sheet counts, and changeovers spent chasing a problem that lives in the roller.
The failure modes are different in every position, which is why we engineer to the position, not to a generic “tissue roller”.
- Lost Emboss Definition
- Adhesive Transfer Drift
- Ply Bond Failure
- Telescoping Logs
- Web Marking
- Compound Hardening
- Lost Vendor
The ABBA Standard
We Engineer to the Position, Not to a Part Number.
Cleat, embosser, glue applicator, laminating, rider, winder: each position has its own compound, finish, hardness, and geometry, and each fails in its own way. We start from the position and the process: your speed, your temperature, and the surface the web needs to see. Covers come from 2,000+ in-house formulations, including food-grade and FDA-compliant compounds where the application requires them, with geometry held to the tolerances the line relies on.
Every roller is verified before it ships, on an approval drawing you signed off before we built it.
Positions We Engineer
The Positions on a Tissue and Towel Line.
Each position asks something different of the roller. Find yours, then the roller type that answers it.
-
Cleat
Cleated and profiled rollers that grip and carry the web or the log without slipping, in a cover that holds its profile and its traction as the shift runs.
-
Embosser
The backing roller that runs against the engraved steel under heat and pressure. Its hardness and resilience set how deep the pattern goes and how long it stays sharp.
-
Glue Applicator
Coating rollers that meter lamination adhesive onto the ply. Finish and hardness set the transfer, so the plies bond without glue bleeding through to the sheet, in food-grade compounds where the application requires them.
-
Laminating
Laminating rollers that marry the plies under even nip pressure across the whole face, so the bond holds edge to edge without crushing the bulk out of the sheet.
-
Rider
Rider rollers ride the building log in the rewinder. They need traction without marking, and runout held tight, or the log winds soft and telescopes.
-
Winder
Winder rollers carry and drive the web at line speed, run after run. Traction, wear resistance, and runout decide whether the log winds tight and true.
Engineering
From reverse engineering and application review to load, stress, and design calculations, we engineer each roller around your process requirements and verify critical tolerances before shipment.
Fabrication
A new roller built to your application, with engineering review and approval before we build.
Surface Technology
Coverings, coatings, and surface finishes engineered to match your process and product requirements.
Material Development
In-house formulations developed around chemistry, temperature, wear, hardness, and performance requirements.
Recover & Repair
Recovering, resurfacing, and repair solutions matched to your roller condition, application, and performance requirements.
Industries
The Other Lines We Engineer For.
We engineer to the specific positions your industry runs. Pick yours.
Tissue Towel
Cliché / Glue Applicators / Embossing / Rider / Winder. Where caliper and uptime matter.
Adhesives & Tape
Coating / Applicator / Metering / Nip / Idler. Where compound, finish, release, and consistency matter.
Robotics & Automation
Wheels / Casters / Drive / Traction / Load. Where movement, wear, and uptime matter.
Agriculture
Abrasion / Weather / Debris / Heavy Duty Cycles. Where wear life in the field is everything.
Additional Industries
Battery & EV, solar, converting, food / FDA, and other critical lines. Don’t see yours? Talk to an engineer.
FAQs
Tissue and Towel Rollers: Common Questions
Which Tissue and Towel Roller Positions Do You Engineer?
Do You Make Food-Grade or FDA-Compliant Rollers?
Can You Replace a Roller on a Converting Line You Have Never Worked On?
Should We Recover Our Tissue and Towel Rollers or Buy New?
How Long Does a Recover Take?
How Do I Get Started?
Roller Evaluation
Put an Engineer on
Your Tissue Line.
Tell us which position is costing you run time.