Bring the Roller You Already Have Back to Spec.

Getting one month out of a roller that should last longer? The fix usually is not a new roller. It is the right compound on the one you have. We strip, re-cover, grind, and finish back to spec, repair damage we find on inspection, and either match your existing material or engineer a longer-lasting one. For a fraction of replacement cost, and often with better wear life than what you had.

Since 1959 Engineered Since 1959
2,000+ Formulations In-House, We Own Them
Inspection TIR to 0.0002″
ISO 9001:2015 Quality Management

Recover or Replace?

If the Core Is Sound, the Fix Is Usually the Cover.

If the core and journals are sound and the design still fits the application, recovering is almost always the better economics. You keep the core and get a fresh, correctly specified cover for a fraction of replacement cost. Replacement makes sense when the core is damaged beyond repair, or when the design itself is what is failing.

An evaluation tells you which. And when a position keeps failing no matter who recovers it, the answer is usually the compound, not the roller, which is why every recover here starts in the lab.

  • Worn Cover
  • Out-of-Round
  • Surface Degraded
  • Cover Delaminating
  • Journal Damage
  • Lost Vendor
  • Spares Running Low

The ABBA Standard

A Recover Is Only as Good as the Compound That Goes Back On.

We develop and own 2,000+ formulations, milled and batch-tested in our own lab. On an incoming recover we can cut a sample and lab-match the material you are running today, or engineer a longer-lasting one where the wear life says we should, which is usually where the gain comes from.

Then the roller is ground and finished back to the drawing, and every critical tolerance is verified before it ships.

In-House Material Development
Application Engineering & Review
Reverse Engineering & Design Support
Verified Tolerances
Approval Drawing Sign-Off
Responsive Lead Times & Expedite Options
Request a Roller Evaluation

From Inspection to Verification

How a Recover
Works

Every recover begins with an inspection and is carried through repair, compound matching, covering, and final verification, so the roller comes back to spec and stays there.

Every Recover Starts with What the Roller Tells Us.

The incoming roller is inspected for core and journal condition, cover wear, runout, and surface damage, and reviewed against the position it runs in. You get a report of what is worn and what to do about it before anything is quoted.

  • Core & Journal Inspection
  • Runout Check
  • Wear-Pattern Review
  • Application Review

The Old Cover Comes Off. The Core Is Made Right.

The worn cover is stripped and the core is prepared for bonding. Journal and core damage found on inspection is repaired in-house, so the recovered roller runs true on the shaft it came with.

  • Cover Stripping
  • Core Preparation
  • Journal & Core Repair
  • Bond Preparation

The Right Material Goes Back On.

A sample of the incoming cover can be lab-tested to match your existing material, or a better-performing formulation is selected from 2,000+ in-house compounds when what you have been running is what is cutting the wear life short.

  • Incoming-Material Lab Matching
  • 2,000+ Formulations
  • Durometer Selection
  • Chemical & Heat Compatibility

Covered and Cured Under Process Control.

The new cover is applied, bonded, and cured using controlled processes designed for consistent, repeatable results, whether the cover is rubber, polyurethane, or a specialty elastomer.

  • Rubber & Urethane Covering
  • Bonding
  • Controlled Curing
  • Specialty Elastomers

Back to Spec, and Proven Before It Ships.

The recovered roller is ground and finished to the drawing, balanced where the speed calls for it, and every critical tolerance is verified and documented before shipment.

  • Precision Grinding
  • Surface Finishing
  • Dynamic Balancing
  • Runout & Cylindricity Verification
  • Quality Documentation

FAQs

Recover & Repair: Common Questions

Should I Recover a Roller or Replace It?
If the core and journals are sound and the design still fits the application, recovering is almost always the better economics. You keep the core and get a fresh, correctly specified cover for a fraction of replacement cost. Replacement makes sense when the core is damaged beyond repair, or when the design itself is what is failing. An evaluation tells you which.
How Long Does a Roller Recover Take?
Typically about three to four weeks for a recover, depending on size and current shop load. New fabrications generally run longer: roughly a month for straightforward builds, and up to two to three months for complex ones. Expedite is available on request and review.
Can You Match the Rubber Compound We Are Using Now?
Yes. On an incoming recover we can cut a sample and lab-test it to match your existing material, or recommend a better-performing formulation if what you have been running is what is cutting your wear life short. See Material Development.
What If the Core or the Journals Are Damaged?
Journal and core repair is done in-house as part of the recover. If the core is damaged beyond repair we will tell you, and quote a new fabrication built to the same drawing, or to a better one. See Fabrication.
Do You Recover Rollers That Another Shop Made?
Yes. Most of the rollers we recover were built elsewhere, and many come from customers whose original source has closed or can no longer hold the tolerance. No drawing is required: we reverse-engineer from the roller itself and produce an approval drawing you sign off on.
How Do I Send a Roller for Recovering?
Request a roller evaluation or send us the basics with a photo of the roller. An engineer reviews it, confirms whether a recover is the right call, and gives you shipping instructions and a quote.

Roller Evaluation

Send Us the Roller You Already Have.

Tell us what’s happening on the line, or ship the roller and we will inspect it and tell you what it will take.