Custom Roller Fabrication to Specification

When you need a new roller, we engineer the core, the journals, the surface, then the finish to the parameters your process actually runs: speed, temperature, chemistry, loading, tension. You sign off on the approval drawing before we build, so what arrives is what you agreed to.

Since 1959 Engineered Since 1959
2,000+ Formulations In-House, We Own Them
Inspection TIR to 0.0002″
ISO 9001:2015 Quality Management

When You Need a New Roller

When the Core Is Gone, or the Design Never Fit, Build New.

A recover keeps your core and puts a fresh cover on it. That only works when the core and journals are sound and the design still fits the position. When the core is cracked, bent, or worn past repair, when the original source has closed, or when the roller was never right for the loads and speeds the line now runs, a new fabrication is the fix. Build-to-print from your drawing, or engineered from the application when there is no drawing to build from.

Ordering a copy of what failed just schedules the next failure. A new build is the chance to correct the design, the compound, and the tolerance in one pass, and to have an engineer confirm all three before anything is cut.

  • Core Beyond Repair
  • Journals Worn Out
  • No Drawing
  • Lost Vendor
  • New Line or Position
  • Design Never Fit
  • Spares Needed

The ABBA Standard

Nothing Gets Built Until You Have Signed the Drawing.

Every new roller starts with an application review and ends with an approval drawing you sign off on before we build. Design is done in-house. The core and journals are fabricated in-house. The cover comes from 2,000+ formulations we develop and own, milled and batch-tested in our own lab, so the compound is chosen for the chemistry, heat, and loading the position sees, not pulled from a catalog.

Then the roller is ground and finished to that drawing, and every critical tolerance is verified before shipment. Wheels and casters for robotics and automation are built from scratch here as well.

In-House Material Development
Application Engineering & Review
Reverse Engineering & Design Support
Verified Tolerances
Approval Drawing Sign-Off
Responsive Lead Times & Expedite Options
Request a Roller Evaluation

From Application Review to Shipment

How Fabrication
Works

Every new roller moves from application review through an approval drawing, in-house core and journal fabrication, covering and curing, and final verification, so the roller that arrives is the roller on the drawing you signed.

It Starts with the Position, Not the Part Number.

Before anything is designed, an engineer reviews where the roller runs and what it has to do there: the web or product it touches, speed, temperature, chemistry, loading, and tension. If you have a drawing, we review it against the application. If you do not, we start from the application and the machine.

  • Application Review
  • Process Parameters
  • Drawing Review
  • Reverse Engineering
  • Failure History

Designed In-House. Approved by You Before We Build.

The roller is designed in-house around that review: core construction, journal geometry, cover material, hardness, finish, and the tolerances that matter for the position. It comes back to you as an approval drawing you sign off on before we build, so the specification is agreed before material is ordered.

  • In-House Design
  • Core & Journal Design
  • Cover Specification
  • Tolerance Callouts
  • Approval Drawing

The Core and Journals Are Made Here.

Cores and journals are fabricated in-house to the approved drawing, in the material and construction the loads and speed call for, then machined true so the cover goes onto a straight foundation. Custom journal configurations and mounting details are part of the build, not an add-on.

  • In-House Core Fabrication
  • Custom Journals
  • Machining
  • Mounting Details
  • Bond Preparation

The Compound Is Chosen for the Position, Then Cured Under Control.

The cover is selected or developed from 2,000+ formulations we own, milled and batch-tested in our own lab: rubber, polyurethane, or a specialty elastomer, matched to the chemistry, heat, wear, and loading the roller will see. It is applied, bonded, and cured under controlled processes for consistent, repeatable results.

  • 2,000+ Formulations
  • Rubber, Urethane & Specialty Elastomers
  • Compound Selection
  • Bonding
  • Controlled Curing

Ground to the Drawing. Proven Before It Ships.

The covered roller is ground and finished to the approved drawing, balanced where the speed calls for it, and every critical tolerance is verified and documented before shipment. Cylindricity to 0.0003″ and TIR to 0.0002″ where the position demands it, with the surface finish the process needs.

  • Precision Grinding
  • Surface Finishing
  • Dynamic Balancing
  • Runout & Cylindricity Verification
  • Quality Documentation

FAQs

Fabrication: Common Questions

When Should I Build a New Roller Instead of Recovering?
When the core or journals are damaged beyond repair, when the design itself is what is failing, or when there is no roller to recover: a new line, a new position, or a source that has closed. If the core is sound and the design fits, recovering is usually the better economics, and we will tell you so. See Recover & Repair.
Do You Build Rollers to Our Print?
Yes. Send the drawing and an engineer reviews it against the application before we quote. If the print carries a tolerance, material, or construction that will not survive the position, we say so and propose the change on the approval drawing, which you sign off on before we build.
What If We Have No Drawing?
We reverse-engineer from the roller you have, or from the machine and the application when there is no roller, and produce an approval drawing you sign off on before we build. See Engineering.
Do You Build Rollers for OEMs and Equipment Builders?
Yes. Most of what we do is custom. We build new rollers, wheels, and casters for equipment builders and integrators, engineered to the position and built to the same approved drawing on every order. Robotic wheels and casters are built from scratch here. See Robotics & Automation.
What Can the Cover Be Made Of?
Rubber, polyurethane, or a specialty elastomer, selected or developed from 2,000+ formulations we own and batch-test in our own lab. The compound is chosen for the chemistry, heat, wear, and loading the position sees. See Material Development, Rubber-Coated Rollers, and Polyurethane Rollers.
How Long Does a New Roller Take to Build?
Typically about three to four weeks for a recover, depending on size and current shop load. New fabrications generally run longer: roughly a month for straightforward builds, and up to two to three months for complex ones. Expedite is available on request and review.

Roller Evaluation

Tell Us What the Roller Has to Do.

Send the drawing, the roller, or just the application. An engineer reviews it and reaches out fast.